PET bottle embryo injection, should pay attention to what?
1, plastic processing because of PET macromolecular contains aliphatic, has certain hydrophilicity, aggregate at high temperature is more sensitive to water, when the moisture content is more than the limit, in the processing of PET molecular weight drops, products with color, crisp. Trapped here, in front of the processing must be carried out on the material drying, the drying temperature is 150 ℃, more than 4 hours, generally is 170 ℃, 3 - 4 hours. Air-launched available to test whether the material completely dry. Generally not more than 25% recycled material and recycled material to dry thoroughly. 2, selection of injection molding machine PET since the stable time is short, after melting point and melting point is high, so need more temperature control section and plasticizing the friction heat generating less injection system, and the products ( Water cut materials) Actual weight can not less than two-thirds of injection machine. Based on these requirements, ramada in recent years, the development of small and medium-sized series of PET special plasticizing system. Clamping force by more than 6300 t/m2. 3, mould and PET bottle embryo gate design general use molding mould of hot flow path, between the mold and injection molding machine template must have the best insulation board, its thickness is about 12 mm, and heat insulation board must be able to bear high pressure. Exhaust must be sufficient to avoid local overheating or fracture, but its vent depth generally not more than 0. 3 mm, otherwise prone to flash. 4, melt temperature available air-launched measure method. 270 - GF - 295 ℃, enhance the level PET can be set to 290 - 315 ℃, etc. 5, generally faster injection, injection speed can prevent premature solidification injection. But too fast, high shear rate makes material brittle. Shot is usually done in 4 seconds. 6, the lower the back pressure, the better to avoid wear and tear. Is generally not more than 100 bar. Usually do not need to use. 7, residence time, do not use the long residence time, in order to prevent the molecular weight decreased. As far as possible avoid temperature above 300 ℃. If the downtime is less than 15 minutes. Just make air-launched processing; If more than 15 minutes, then use PE clean, viscosity and the barrel temperature drop to PE, until it is. 8, note (1) recycling materials can't be too big, otherwise easy to produce the materials' bridging 'which might affect the plasticizing. 2 if the mold temperature control is not good or improper material temperature control, easy to produce 'white mist and opaque. Die temperature low and uniform, cooling speed, transparent crystal is less products.
How do small and medium-sized enterprises develop product of cosmetics.
1. Don’t make too many products. There are more and more small and medium-sized cosmetic manufacturers. Their products almost cover all kinds of cosmetics. You can see that there are many products, but in fact, they have many disadvantages. The first one is that the sales volume is not necessarily high. The 80/20 law states that 80% of the benefits of any entity come from 20% of the products, that is, 80% of the products can only contribute 20% of the benefits, which is not economic. The second one is that too many product lines are relatively backward in management, and their own strength is insufficient, enterprises can’t grasp the dynamics of consumers' hearts, so there are a lot of products which are not need by consumers. Third, most companies focus on speculation and bargain hunting. Too many product lines limit the development of an enterprise. It is difficult for consumers to form an understanding of the enterprise without a major product. And it is impossible to find the market position without the c
Cosmetic tube field, where is the foothold in the future?
Nowadays, in order to meet the changing needs of consumers, whether it is basic skin care brands or efficacy brands, when most of them launch new series of products, they will launch matching products with instruments, aiming to realize the effective incorporation of brands through high-tech instruments.
About D19 Vibration eye cream tube
Innovative and practical packaging materials not only greatly improve the manufacturing technology, but also have more advantages in practicality than traditional packaging materials. This is a high-tech eye cream hose, bringing the eye cream package into a brand new era.
What are the customers' concerns about cosmetic packaging enterprises
In the choice of cosmetics package enterprises, first of all to see whether the qualification of the enterprise is in line with the requirements of the national cosmetic package production. If the enterprise's qualification is blurred, it shows that the enterprise does not meet the national production requirements and the quality of the product can not be guaranteed. So when choosing cosmetic packaging enterprises, we must check the production qualification of enterprises.
What is the two in one tube and how to fill it in the rear? And the application of the product in skin care
Unlike a single branch tube, the most intuitive tube is a tube in the tube, which looks like a single branch, but can fill two kinds of material at the same time, at the same time extruding. When the material is not used, the material body is separated, and when used, mingling and merging.