Español 
Latest products
Common faults SBO2 cosmetics packaging production machine equipment
by：Lisson
2020-11-25
1: charging not charging: need to check several ways:
whether there had been no material hopper, if it is: to feed the
not: please check whether the elevator control contactor in electrical state, if it is electrical state, to check whether the motor is in power and load state, because this kind of circumstance is Ken can is by cosmetics packaging production embryo stuck with ascension, then the simplest method is to promote human help.
if you check the elevator control contactor is not to state, please check whether the embryo to detect magic eye cosmetics packaging production and baffle plate is not on the same line.
2: feed themselves feed table: this kind of circumstance is a headache problem, empirically if the length of the cosmetics packaging production embryos longer cut weight is bigger, so this kind of phenomenon is less.
if always happen such problem, be sure to check incoming material plate installation position and height is correct, the other can pen marking the following each mold installation location, easy to adjust for the next installation.
3: cosmetics packaging production after the child into cannot be removed from the mold.
first of all should open the mold, mold clamping mould in manual mode, if is normal, but just to run in with empty running status, if is normal.
please check your Settings, exhaust time if the exhaust set to normal, and every time as long as a cosmetics packaging production failure, then can judge is the problem of exhaust valve, please open the exhaust valve check its spring and seal ( This kind of failure is also a phenomenon is the exhaust noise is larger or have not the voice of the net) 。
if you meet a lot of mold production normal chance to check on the open mold, please check the lock pin if there is a section of the screw inside, please check whether the clamping force is too big, if too big should be readjusted according to the standard.
4: cosmetics packaging production child always task of
the usage of this kind of situation need to check the clip manipulator, elastic spring has the position of the manipulator is misplaced. 5:
collision of two mechanical hand in this kind of situation need to be manually reset manipulator, is caused by misalignment.
reprint please indicate the source: the packaging of cosmetics packaging production network
whether there had been no material hopper, if it is: to feed the
not: please check whether the elevator control contactor in electrical state, if it is electrical state, to check whether the motor is in power and load state, because this kind of circumstance is Ken can is by cosmetics packaging production embryo stuck with ascension, then the simplest method is to promote human help.
if you check the elevator control contactor is not to state, please check whether the embryo to detect magic eye cosmetics packaging production and baffle plate is not on the same line.
2: feed themselves feed table: this kind of circumstance is a headache problem, empirically if the length of the cosmetics packaging production embryos longer cut weight is bigger, so this kind of phenomenon is less.
if always happen such problem, be sure to check incoming material plate installation position and height is correct, the other can pen marking the following each mold installation location, easy to adjust for the next installation.
3: cosmetics packaging production after the child into cannot be removed from the mold.
first of all should open the mold, mold clamping mould in manual mode, if is normal, but just to run in with empty running status, if is normal.
please check your Settings, exhaust time if the exhaust set to normal, and every time as long as a cosmetics packaging production failure, then can judge is the problem of exhaust valve, please open the exhaust valve check its spring and seal ( This kind of failure is also a phenomenon is the exhaust noise is larger or have not the voice of the net) 。
if you meet a lot of mold production normal chance to check on the open mold, please check the lock pin if there is a section of the screw inside, please check whether the clamping force is too big, if too big should be readjusted according to the standard.
4: cosmetics packaging production child always task of
the usage of this kind of situation need to check the clip manipulator, elastic spring has the position of the manipulator is misplaced. 5:
collision of two mechanical hand in this kind of situation need to be manually reset manipulator, is caused by misalignment.
reprint please indicate the source: the packaging of cosmetics packaging production network
Custom message
